|
|
|
|
|
Murat Demiral, Fethi Abbassi, Abolfazl Zahedi and Salih Akpinar
Single shear or single lap joints are the most prevalent type of adhesive joints used in advanced engineering applications, where they are exposed to fatigue loadings in their services. Although their mechanical performances under static loading have bee...
ver más
|
|
|
|
|
|
|
|
|
|
|
Murat Demiral, Fethi Abbassi, Riaz Muhammad and Salih Akpinar
Bonded joints used in wing sections and frames of aircraft structures are mostly exposed to cyclic loadings instead of static ones during their services. Bending types of dynamic loadings are mostly encountered. In this study, the fatigue response of a s...
ver más
|
|
|
|
|
|
|
|
|
|
|
Feng Hu and Hongbing Xin
The flexible bearing is the kernel component of the cam wave generator. In precision transmission applications such as miniature robot joints, flexible bearings are required to have a smaller mass, lower moment of inertia, and larger inner diameter. Base...
ver más
|
|
|
|
|
|
|
|
|
|
|
Wei Peng and Weijie Fan
In order to study the corrosion time-varying law and fatigue properties of high-strength steel strands used for marine environment structures, the accelerated corrosion test of steel strands was carried out by using a climate simulation chamber, and samp...
ver más
|
|
|
|
|
|
|
|
|
|
|
Wenxiang Yang, Yaozhen Han, Ronglin Ma, Mingdong Hou and Guang Yang
The floating platform motion of an offshore wind turbine system can exacerbate output power fluctuations and increase fatigue loads. This paper proposes a new scheme based on a fast second-order sliding mode (SOSM) control and an adaptive super-twisting ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yusuf O. Busari, Yupiter H. P. Manurung, Martin Leitner, Yusuf L. Shuaib-Babata, Muhd F. Mat, Hassan K. Ibrahim, David Simunek and Mohd Shahar Sulaiman
This research presents the numerical evaluation of fatigue crack growth of structural steels S355 and S960 based on Paris? law parameters (C and m) that are experimentally determined with a single edge notched tension (SENT) specimen using optical and cr...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhiping Zeng, Ji Hu, Xudong Huang, Weidong Wang, Zhibin Huang, Abdulmumin Ahmed Shuaibu, Yu Yuan, Zhonglin Xie and Xianfeng He
To meet the transportation requirements of heavy-haul trains, it is necessary to consider the use of prestressed reinforced concrete ballastless tracks. Therefore, the CRTSIII SBT (China Railway Track System III-type slab ballastless track) has been cons...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhiqiang Xu, Yunxian Cui, Baoliang Li, Ketong Liu, Feiting Shi and Peng Cao
A fatigue test on the failure mode of flange shafts was conducted. The propagation characteristics of the initial crack at the junction between the shaft and the flange as well as its angle effect were studied. This study developed an analysis program of...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ivana Gledic, Antonio Mikulic and Jo?ko Parunov
Specialized procedures to help in the emergency response situations following ship accidents have been under development by the Classification Societies. Such procedures consider the hull-girder collapse as the most important failure mode, without the po...
ver más
|
|
|
|
|
|
|
|
|
|
|
Andrej Atrens, Qian Liu, Clotario Tapia-Bastidas, Evan Gray, Bartolomeus Irwanto, Jeff Venezuela and Qinglong Liu
The influence of hydrogen on the mechanical properties of four, medium-strength, commercial, quenched-and-temped steels has been studied using the linearly increasing stress test (LIST) combined with cathodic hydrogen charging. The relationship was estab...
ver más
|
|
|
|
|
|