|
|
|
|
|
Zhuang Wang, Bing Wang, Haozhe Jiang and Ping Zhuge
To investigate the influence of external prestressing with carbon fiber-reinforced polymer (CFRP) tendons on the flexural and shear performance of reinforced concrete beams, a total of six simply supported beams with a length of 3.5 m and two two-span co...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hao Su, Monssef Drissi-Habti and Valter Carvelli
This work is a follow-up to previous research by our team and is devoted to studying a dual-sinusoidal placement of distributed fiber-optic sensors (FOSs) that are embedded inside an adhesive joint between two composite laminates. The constructed smart c...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yubing Yuan, Yicai Ji, Shengbo Ye, Xiaojun Liu and Guangyou Fang
Life detection is important in earthquake rescue, but weak vital signal is susceptible to interference by clutters. Due to the undesirable characteristics of the hardware, there are two main types of clutter generated by the frequency modulation continuo...
ver más
|
|
|
|
|
|
|
|
|
|
|
Shouju Miao, Xiaojian Zhan, Yangbing Yuan and Lijun Jia
This study investigates the mechanical performance of a polyester fiber concrete continuous rigid frame bridge during construction and the spatial stress distribution of the 0# block box girder, with a focus on the backdrop of the bridge in Pipa Zhou, Ji...
ver más
|
|
|
|
|
|
|
|
|
|
|
Nikita R. Poddubrovskii, Ivan A. Lobach and Sergey I. Kablukov
We report on the development of an optical frequency domain reflectometry (OFDR) system based on a continuous-wave Er-doped self-sweeping fiber laser. In this work, we investigate the influence of the input data processing procedure in an OFDR system on ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Liv Rittmeier, Natalie Rauter, Andrey Mikhaylenko, Rolf Lammering and Michael Sinapius
Lamb waves occur in thin-walled structures in two wave modes?the symmetric and the antisymmetric mode. Their oscillation on the structures? surfaces is either in phase (symmetric) or shifted by a phase angle of ??
p
(antisymmetric). In this work, a meth...
ver más
|
|
|
|
|
|
|
|
|
|
|
Huangjun Zeng, Wenze Xue, Robert T. Murray, Weidong Chen, Zhongben Pan, Li Wang, Chen Cui, Pavel Loiko, Xavier Mateos, Uwe Griebner and Valentin Petrov
We investigate in-band pumping of a Tm,Ho,Lu:CaGdAlO4 laser using a Raman-shifted Er-fiber laser (1678 nm), in the continuous-wave (CW) and mode-locked (ML) regimes. A maximum output power of 524 mW is obtained in the CW regime with a 5% output coupler a...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yiliang Sun, Jingwen Li and Hongfu Li
Thermoplastic resin matrix has a high melt viscosity, which is difficult to impregnate with fibers. The addition of flame retardant will further increase the viscosity of the melt and increase the difficulty of impregnation. It is possible to reduce the ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yogesh Gandhi and Giangiacomo Minak
Topology Optimization (TO) recently gained importance due to the development of Additive Manufacturing (AM) processes that produce components with good mechanical properties. Among all additive manufacturing technologies, continuous fiber fused filament ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Tim Heitkamp, Simon Girnth, Sebastian Kuschmitz, Günter Klawitter, Nils Waldt and Thomas Vietor
An existing challenge in the use of continuous fiber reinforcements in additively manufactured parts is the limited availability of suitable fiber materials. This leads to a reduced adaptability of the mechanical properties to the load case. The increase...
ver más
|
|
|
|
|
|