|
|
|
Fuad Albani,Megga Ratnasari Pikoli,Irawan Sugoro
Pág. 264 - 270
Elephant dung is a source of methane gas, which the gas is the main contributor to greenhouse gas if not used as fuel. Wild elephants use grass leaves as their feed, but in Ragunan Wildlife Park, elephants are fed also with a combination of elephant gras...
ver más
|
|
|
|
|
|
|
Lijun Ma, Meng Sun and Yunlong Zhang
In order to facilitate waste glass recycling and enable the monitoring of concrete structures, this study prepares a new type of self-sensing engineered cementitious composite (ECC) via the use of glass sand instead of silica sand. The health monitoring ...
ver más
|
|
|
|
|
|
|
Fengge Li, Chen Chen and Zehui Xiang
To investigate the effects of concrete canvas (CC) and carbon fiber reinforced plastic (CFRP) reinforcement on the mechanical properties of corroded reinforced concrete columns (compressive strength, flexure strength, strength of extension, and so on), 4...
ver más
|
|
|
|
|
|
|
Huile Zhang, Zeyu Sun, Pengpeng Zhi, Wei Wang and Zhonglai Wang
This paper develops a material-structure integrated design and optimization method based on a multiscale approach for the lightweight design of CFRP car doors. Initially, parametric modeling of RVE is implemented, and their elastic performance parameters...
ver más
|
|
|
|
|
|
|
Shun-Fa Hwang, Yi-Chen Tsai, Cho-Liang Tsai, Chih-Hsian Wang and Hsien-Kuang Liu
A finite element simulation was utilized in this work to analyze the thermoforming process of woven carbon fiber fabric/polyurethane thermoplastic composite sheets. In the simulation that may be classified as a discrete method, the woven carbon fiber fab...
ver más
|
|
|
|
|
|
|
Kiho Nishihara, Kei-ichi Okuyama, Rafael Rodriguez and Isai Fajardo
In this study, we focus on 3D-printed PEEK/CFRTP (Carbon-Fiber-Reinforced Thermoplastic) and PEEK (Polyether Ether Ketone) materials as new space materials. In space, there are intense ultraviolet (UV) rays that are weakened by the atmosphere on Earth, s...
ver más
|
|
|
|
|
|
|
Jordi Renau Martínez, Víctor García Peñas, Manuel Ibáñez Arnal, Alberto Giménez Sancho, Eduardo López González, Adelaida García Magariño, Félix Terroba Ramírez, Francisco Javier Moreno Ayerbe and Fernando Sánchez López
This article presents the design and manufacturing of a hydrogen-powered unmanned aquatic surface vehicle (USV) hull. The design process comprised three stages: (1) defining the requirements for a preliminary geometry, (2) verifying the hydrodynamic hull...
ver más
|
|
|
|
|
|
|
Carlo Boursier Niutta, Pierpaolo Padula, Andrea Tridello, Marco Boccaccio, Francesco Acerra and Davide S. Paolino
This paper deals with an innovative nondestructive technique for composites (local-IET), which is based on the Impulse Excitation Technique (IET) and, in the presence of damage, assesses the degradation of the elastic properties of a local region of the ...
ver más
|
|
|
|
|
|
|
Touraj Farsadi, Majid Ahmadi, Melin Sahin, Hamed Haddad Khodaparast, Altan Kayran and Michael I. Friswell
In the field of aerospace engineering, the design and manufacturing of high aspect ratio composite wings has become a focal point of innovation and efficiency. These long, slender wings, constructed with advanced materials such as carbon fiber and employ...
ver más
|
|
|
|
|
|
|
Christoforos S. Rekatsinas, Dimitris K. Dimitriou and Nikolaos A. Chrysochoidis
The present paper investigates the design process and the dimensioning of a tailless type-C composite sandwich unmanned aerial vehicle (UAV). The objective is to investigate an innovative aircraft configuration which exceeds the standard approach of ribs...
ver más
|
|
|
|