|
|
|
|
|
Wenjie Shen, Suofang Wang and Xiaodi Liang
Impellers are utilized to increase pressure to ensure that a radial pre-swirl system can provide sufficient cooling airflow to the turbine blades. In the open literature, the pressurization mechanism of the impellers was investigated. However, the effect...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jianfeng Zhu, Guochen Huang, Maoguang Xu, Ming Liu, Bo Diao and Po Li
Combined with the development trend of high speed generators and the high voltage of DC microgrids in high-power series hybrid aero propulsion system, a set of hybrid systems with a power of 200 kW, voltage of 540 V, and speed of 21,000 r/min is establis...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ali Dinc, Ali Mamedov, Ertugrul Tolga Duran, Fethi Abbassi, Ibrahim Elbadawy, Kaushik Nag, Mehdi Moayyedian, Mohamed Fayed, Murat Otkur and Yousef Gharbia
In this study, the effect of inlet air cooling on greenhouse gas (GHG) emissions and engine performance for a land-based gas turbine engine was investigated under varying ambient temperatures (15?55 °C). The study aimed to reduce GHG emissions while impr...
ver más
|
|
|
|
|
|
|
|
|
|
|
Artur Kulaszka, Józef Blachnio and Henryk Borowczyk
The reliability and operational safety of an aircraft engine gas turbine are extremely important in terms of its operation. In the course of operation, these turbines undergo complex thermal, mechanical, aerodynamic, and chemical exhaust gas loads. Due t...
ver más
|
|
|
|
|
|
|
|
|
|
|
Shuai Ma, Yafeng Wu, Hua Zheng and Linfeng Gou
Aiming at engine health management, a novel hybrid prediction method is proposed for exhaust gas temperature (EGT) prediction of gas turbine engines. This hybrid model combines a nonlinear autoregressive with exogenous input (NARX) model and a moving ave...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yibing Xu, Lei Gao, Ruizhe Cao, Chong Yan and Ying Piao
Currently, an increasing number of designers have begun to pay attention to a new paradigm for evaluating the performance with full engine 3-dimensional computational fluid dynamics (3D CFD) simulations. Compared with the traditional component-based perf...
ver más
|
|
|
|
|
|
|
|
|
|
|
Razvan Nicoara, Daniel Crunteanu and Valeriu Vilag
As a main component of most gas-turbine engines, the axial flow turbines have been in a process of continuous improvement, reaching high efficiencies and reliability. A well-known drawback of these systems is the rapid decrease in performance when operat...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ioannis Kolias, Nikolaos Aretakis, Alexios Alexiou and Konstantinos Mathioudakis
Disks in gas turbines are optimized for minimum weight, while satisfying both geometry and stress constraints, in order to minimize the engine production, operation, and maintenance costs. In the present paper, a tool is described for the preliminary mec...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhaohui Yao, Yuanzhao Guo, Jun Niu, Zhiguang Jin, Tianhao Yu, Baojun Guo, Wenhao Pu, Xin Wei, Feng Jin, Bo Li and Mengying Liu
A model of a NUAA-PTRE pre-cooled air turbine engine was established. The design point parameters of the engine were optimized, including the pressure ratio, air flow rate of the compressor, efficiency, throat area, and efficiency of the turbine. The air...
ver más
|
|
|
|
|
|
|
|
|
|
|
Kefu Wang, Yiqun Ao, Kai Zhao, Tao Zhou and Feng Li
Shaped cooling holes have received considerable attention in recent years due to their potential to improve heat transfer while minimizing pressure drop. In this study, the effects of lobe-shaped cooling holes on film cooling performance and turbulent fl...
ver más
|
|
|
|
|
|