Collision Risk Assessment Support System for MASS RO and VTSO Support in Multi-Ship Environment of Vessel Traffic Service Area

Abstract

The discussions by the International Maritime Organization for the introduction of a maritime autonomous surface ship (MASS) began in earnest. At the 27th ENAV meeting, the International Association of Marine Aids to Navigation and Lighthouse Authorities proposed the “sharing of a common operating picture for situational awareness of the waterway within vessel traffic service (VTS) environment” when developing a system to support MASS operation. Marine accidents caused by collisions on waterways still account for a high percentage of ship accidents that occur at sea, and many studies have investigated the risk of collision between ships. Collision risk assessment was primarily conducted in ship domain-based safety areas. This study evaluates the collision risk using the ship domain derived by the VTS operator (VTSO) and proposes a real-time collision risk assessment support system to improve the situational awareness of VTSOs and MASS remote operators (MASS ROs) regarding near-collision situations occurring in local waters. To evaluate the validity of the proposed system, a risk analysis was performed on near-collision scenarios at Busan Port. The results show that the distance to the closest point of approach (CPA), time to the CPA, and inter-ship distance converged within 0.5 nautical miles, 10 min, and 3 nautical miles, respectively.

1. Introduction

The International Maritime Organization (IMO) included discussions of maritime autonomous surface ships (MASSs) in the official agenda of the 99th meeting of the Maritime Safety Committee (MSC) in 2018, and they have prepared a regulatory scoping exercise (RSE) for MASS operation [1,2,3,4,5,6]. The discussions have defined MASS vessels for RSE work and categorized their autonomy level (degree one: ship with automated processes and decision support; degree two: remotely controlled ship with seafarers on board; degree three: remotely controlled ship without seafarers on board; degree four: fully autonomous ship) [1]. The autonomy level of MASSs is divided into levels 1 and 2, in which a crew is on board, and levels 3 and 4, in which no crew is on board. Levels 2 and 3 represent the concept of a remote operator (RO), which remotely controls a MASS vessel from the remote control center (RCC) on shore. Remote operation requires the development of collision risk assessment technology to determine the MASS collision risk at sea.

The International Association of Marine Aids to Navigation and Lighthouse Authorities (IALA) has been discussing its support of MASS operations at each stage of the IMO discussions on the relevant agreements for MASS operations. The Draft MASS Guideline was submitted at the 27th meeting of the e-Navigation Information Services and Communications (ENAV) committee for the implementation and testing of MASS systems following the introduction of MASSs, and nine prior considerations were proposed to provide system guidance to support MASS operations [7,8]. The document contains points related to the “sharing of a common operating picture for situational awareness of the waterway within vessel traffic services (VTS) environment” and “scoping and development of guidance on the interaction between VTS and the control for MASS shore control center (SCC),” among the prior considerations of MASS system guidance. In many cases, because the lack of situational awareness leads to an accident due to human error, situational awareness in dangerous waters could help prevent accidents [9,10,11,12,13,14]. Therefore, when implementing a system for the situational awareness of collision risks in VTS areas and the interaction between MASSs and VTS centers, collision risk assessment and support technologies for VTS operators (VTSOs) and ROs in multi-ship encounter situations in VTS areas must be implemented in a real-time system as a key module.

Fujii and Tanaka, 1971 [15] proposed the concept of an empirical ship domain model to evaluate the risk of collision based on the ship encounter situation at sea. Subsequently, a ship operator survey and an empirical ship domain model based on RADAR and AIS data were introduced by Coldwell, 1983 [16], Goodwin, 1975 [17], Hansen et al., 2013 [18], and Wang and Chin, 2016 [19]. In addition, various ship domain models based on expert knowledge, computer simulation, neural networks, fuzzy neural networks, analytical traffic, multi-ship conflict complexity, and safety analysis were proposed to evaluate the risk of ship collisions [20,21,22,23,24,25,26,27,28,29]. This ship domain-based risk assessment determines whether the domains of one’s own ship and other ships invade each other at the current location; however, the method is limited because the risk of a collision at the closest point of approach (CPA) location could not be evaluated in advance if the current voyage continued. Therefore, Yoo and Lee, 2019 [30] proposed a collision risk index (CoRI) model based on the concept of the ship domain at the CPA to calculate the subjective collision risk from the perspective of a VTSO for ship collisions in VTS areas depending on the distance to collision, time to collision, and encounter attitude risk between ships. The ship collision risk determined by the CoRI model is similar to that determined by an RO that remotely controls MASS vessels because both assess possible ship collision risk situations in the VTS control center via a VTSO.

The collision alert system (CAS), which can evaluate real-time risk situations in multi-ship environments, is known to improve the VTSO’s situational awareness of local waters [31,32], and the CAS system generates a warning alarm when the distance to the CPA (DCPA) and time to the CPA (TCPA) are below the set value [32,33,34,35,36]. In addition, studies related to CAS systems include heuristic criteria to evaluate the collision risk, which was proposed by Patraiko et al., 2010, Hilgert and Baldauf, 1997, and Baldauf et al., 2011 [37,38,39], fuzzy systems proposed by Bukhari et al., 2013, Kao et al., 2007, and Ren et al., 2011 [40,41,42], quantitative risk assessment applied dynamic adjustment by Mou et al., 2010 [43], and CAS regression modeling by Chin and Debnath, 2009 [33]. In addition, Baldauf and Fischer, 2019 conducted a simulation experiment that assumes a preliminary situation wherein MASS ships and existing ships operate in common in the VTS area, and they compare the actions taken by groups with and without navigation experience against collision risk situations [44]. In this experiment, the authors derived issues (such as the qualification and training of the RO, existing systems that should be further updated for the RO’s situation awareness, etc.) that should be reflected in the future CAS system for the situation awareness of the ROs.

The purpose of this study is to develop a real-time collision risk assessment support system that provides the VTSO and MASS RO with related graphic information and quantitative data on the risk situations in local waters in the event of a near-collision situation in the VTS area where multiple ships navigate. To this end, the safety area ship domain model by the VTSO provides a CoRI risk value according to the ship encounter situation of multiple ships to improve the situational awareness of local waters by generating an alarm in the event of a near-collision situation. Section 2 describes the CoRI model and risk assessment method, and Section 3 presents the results of the collision risk analysis for near-collision scenarios. Section 4 proposes a risk assessment algorithm and a collision risk assessment support system (RiASS) configuration for VTSO and MASS RO situational awareness in a multi-ship environment. Finally, Section 5 summarizes the limitations and key points of this study.

2. Methodology

A collision risk assessment module is proposed to evaluate the collision risk caused by multi-ship environments in the VTS area, and support VTSO and RO control and remote evacuation. The module is based on the number of combination cases within the minimum separation distance between ships i and j, and it sends an alarm to the VTSO and RO systems if the collision risk index output exceeds the set value. The collision risk models and methodologies to evaluate the collision risk in multi-ship environments are described in the following subsections.

2.1. Collision Risk Model

Based on the ship domain at the CPA position, the CoRI model, in which the VTSO assesses the risk of collision for ship encounters at sea, yields risk indices according to the inter-ship encounter, and it finally estimates the value of the CoRI that reflects the risk attitude of the VTSO.

The encounter risk E_ij between ship-i and ship-j is expressed as follows in the head-on, crossing, and overtaking scenarios for the two vessels:

$$E_{ij}=R_{cpa}\left({\theta }_i\right)+R_{cpa}\left({\theta }_j\right)$$

(1)

$$R_{cpa}^{ij}{}_{cpa}\left({\theta }_{ij}\right)=\left\{\begin{array}{cc}a\sec \mathrm{h}\left(d\theta \right) & , \mathrm{if} 0\le \theta <\frac{2\pi }{3} \\ b\sec \mathrm{h}\left(e\left(\theta -\pi \right)\right) & , \mathrm{elseif} \frac{2\pi }{3}\le \theta <\frac{3\pi }{2}\\ c\sec \mathrm{h}\left(f\left(\theta -2\pi \right)\right)& , \mathrm{else} \frac{3}{2}\le \theta <2\pi \end{array}\right.$$

(2)

Here, $R_{cpa}^{ij}$ is the encounter risk according to the relative bearing ${\theta }_{i,j}$ from ship-i, j; a, b, and c are the coefficients determined by the bow or stern maximum risk value of the ship; and d, e, and f are the coefficients determined by the risk level of the encounter situation.

The risk A_ij according to ship-to-ship proximity is expressed as an index that quantitatively represents the proximity risk of the target ship using the safety distance $D{s}_{ij}$ of the ship domain at the CPA position and the proximity index $R_{sd}$, which indicates the proximity of the ship:

$$A_{ij}=R_{sd}^i\left(l\right)+R_{sd}^j\left(l\right)$$

(3)

$$R_{sd}\left(f_{ij}\right)=\mathrm{sech}\left(g·f_{ij}\right)$$

(4)

$$f_{ij}=\mathrm{DCPA}·D{s}_{ij}^{-1}$$

(5)

Here, $R_{sd}$ is the approaching risk index from ship-i, j considering the safety domain, $g$ is the coefficient determined by the risk level in the VTSO domain, $f_{ij}$ is the approaching factor based on the DCPA and VTSO domain for ship-i, j at the CPA position, and $D{s}_{ij}$ is the safety distance from the CPA to VTSO domain intersection for ship-i, j.

The hazard of ship-to-ship proximity T_ij is an index that quantitatively represents the proximity hazard of ship-i and ship-j, and it considers the effect of each factor that constitutes the ship’s specifications on the time remaining until the collision.

$$T_{ij}=R_{at}^i\left(\tau \right)+R_{at}^j\left(\tau \right)$$

(6)

$$R_{at}^{ij}\left(\tau \right)=\left\{\begin{array}{cc}\mathrm{sech}\left(h\tau \right)& ,\mathrm{if} \tau \ge 0 \\ \mathrm{sech}\left(kt\right)& ,\mathrm{else} \tau <0 \end{array}\right.$$

(7)

$${\tau }_{ij}={\tau }_{\min }·\left(1-\frac{I_{\mathrm{type}}^{ij}+I_{\mathrm{loa}}^{ij}+I_{\mathrm{beam}}^{ij}+I_{\mathrm{draft}}^{ij}+I_{\mathrm{time}}^{ij}}{100}\right)$$

(8)

Here, $R_{at}^{ij}$ is the risk related to the approaching time from ship-i or ship-j, $h \mathrm{and} k$ are the coefficients determined by the VTSO from the time risk value, ${\tau }_{ij}$ is the time to the collision for ship-i or ship-j, ${\tau }_{\min }$ is the minimum approach time based on the displacement between the ships, and $I_{\mathrm{type}}^{ij}, \cdots , I_{\mathrm{time}}^{ij}$ are the parameters of ship-i or ship-j that affect the time allowance, such as ship type, length, beam, draft, and navigation time.

The collision risk index RI is expressed as the product of the risk indices $E_{ij}$, $A_{ij}$, and $T_{ij}$, as follows:

$$R{I}_C\left(t\right)=E_{ij}·A_{ij}·T_{ij}$$

(9)

$$CoR{I}_C\left(t\right)=\frac{P_{\max }}{1-\exp \left(\rho \right)}·\left[1-\exp \left(-\rho ·\frac{-RI\left(\mathrm{t}\right)}{R{I}_{\max }}\right)\right]$$

(10)

where $R{I}_C$ is the ship collision risk index between the ship-i, j combination at time $t$, $R{I}_{\max }$ is the maximum value of the ship collision risk index ($R{I}_{\max }=8$), $P_{\max }$ is the maximum value of the ship collision risk ($P_{\max }=6$), and $\rho$ is the VTSO risk attitude. $CoR{I}_C$ is the collision risk combination between ships i and j in a specific area at time $t$.

2.2. Collision Risk Assessment

The International Regulations for Preventing Collisions at Sea (COLREG) Rule 22 states that the minimum sidelight visibility for ships over 50 m is 3 nautical miles [45,46]. Therefore, we propose Risk Assessment (RiAS), which is a collision risk assessment module that yields a CoRI value for all vessel cases within a minimum separation distance of 3 miles for ship-to-ship operations in a multi-ship environment. Additionally, it generates alarms if the reference values set by the VTSO and RO systems are exceeded:

$$RiA{S}_C^{ij}\left(t\right)=Alar{m}_C^{ij}\left(t\right)\left\{\begin{array}{cc} 0& ,\mathrm{if} CoR{I}_C\left(t\right)<50\% \\ 1& ,\mathrm{else} CoR{I}_C\left(t\right)\ge 50\% \mathrm{and} Dis{t}_C^{ij}\left(t\right)\le 3\mathrm{NM}\end{array}\right.$$

(11)

where $RiA{S}_C$ is the collision risk assessment value between the ship-i, j combination at time $t$, $Alar{m}_C$ is the collision risk assessment value between ships i and j at time $t$, which returns a 0 or 1 value if the alarm is off or on, respectively, and $Dis{t}_C$ is the distance in nautical miles between ship-i and j at time $t$.

In the event of an alarm in the RiAS module, the VTSO and RO may take action to avoid collisions, including course changes and speed limits. These actions must consider the maneuverability performance and encounter relationships between ships.

Meanwhile, the VTSO risk attitude $\rho$ used in Equation (10) is an attitude of VTSO that can be used to determine the collision risk for situation awareness (or risk situations), and it was derived through a collision risk determination questionnaire for 135 VTSOs working at Korean VTSs in coastal waters [47]. The same value as VTSO risk attitude was applied to RO risk attitude because the MASS vessel is not yet in the operation stage but from the perspective of controlling ships.

3. Analytic Results

The ship traffic data of collision risk situations in the Busan Port VTS area were used to evaluate the collision risk in multi-ship environments for three near-collision (CoRI $\ge$ 50%) scenarios [29].

3.1. Multi-Ship Environment Situation

The near-collision risk situation used the debriefing system data from the Busan Port VTS on 27 July 2018 [48,49], which lasted for approximately 20 min during the dawn: 05:33:05 to 05:53:35 a.m.

Figure 1 shows the collision risk situation of the Busan Port VTS debriefing system at time 05:50:27. Ship-1, 2, 5, and 6 were entering the port of Busan sequentially, and ship-3, which is a tugboat, was crossing the Busan Port fairway separation zone, thus causing a risk of collision with the inbound ships. Therefore, the VTSO was adjusting the entry order and risk situation of the inbound ships.

Figure 1. Shows static data from ships 1–6 navigating the VTS area of Busan Port in a collision risk situation. Six multi-ships sailed during that time, with four container ships, one ferry, and a tugboat passing each other. The ship specifications, including length, beam, and draft information, are shown in

Table 1. Ship data with dimensions and ship types.

Ship No.	Ship Type	Dimensions [m]
		Length	Beam	Draft
ship-1	container	162	26	5.9
ship-2	container	132	19	6.5
ship-3	tug	23	6.5	2
ship-4	container	137	25	7.9
ship-5	passenger ship	162	25	5.6
ship-6	container	142	20	7.3

.

Figure 1. Shows static data from ships 1–6 navigating the VTS area of Busan Port in a collision risk situation. Six multi-ships sailed during that time, with four container ships, one ferry, and a tugboat passing each other. The ship specifications, including length, beam, and draft information, are shown in Table 1.

3.2. Collision Risk Analysis Results

Figure 2 shows the results of plotting the navigation information for ships 1–6 using a 3-min vector during the collision risk situation between 05:33:05 and 05:53:35. At this point, ○ indicates the starting position of the ship-track 3-min vector. The navigation results in Figure 2 show that ship-1 (blue), ship-2 (cyan), ship-5 (magenta), and ship-6 (red) are traveling leftward in the northwest direction, and ship-3 (green) is traveling leftward in the southwest direction. In addition, it can be observed that ship-4 (black) is sailing right from north-west to south-east.

For the total number of ships (n) navigating the VTS area in collision risk situations, the combination number with which ship-i, j (k) can encounter a collision situation is n!/k!(n − k)!. A total of 15 collision combination numbers are shown in Figure 2.

Table 2. Scenario combinations for target ships under near-collision situations in Busan Port VTS area during time 05:33:05–05:53:35.

Scenario No.	Target Ships (ship-i, ship-j)	Initial Speed [kts]	End Speed [kts]	Initial Course [°]	Time [hh:mm:ss]
no.1 no.2 no.3 no.4 no.5	ship-1, ship-2 ship-1, ship-3 ship-1, ship-4 ship-1, ship-5 ship-1, ship-6	11, 14 11, 4 11, 14 11, 15 11, 11	8, 11 8, 4 8, 15 8, 10 8, 9	324, 322 324, 209 324, 116 324, 311 324, 318	05:33:05 – 05:53:35
no.6 no.7 no.8 no.9	ship-2, ship-3 ship-2, ship-4 ship-2, ship-5 ship-2, ship-6	14, 4 14, 14 14, 15 14, 11	11, 4 11, 15 11, 10 11, 9	322, 209 322, 116 322, 311 322, 318
no.10 no.11 no.12	ship-3, ship-4 ship-3, ship-5 ship-3, ship-6	4, 14 4, 15 4, 11	4, 15 4, 10 4, 9	209, 116 209, 311 209, 318
no.13 no.14	ship-4, ship-5 ship-4, ship-6	14, 15 14, 11	15, 10 15, 9	116, 311 116, 318
no.15	ship-5, ship-6	15, 11	10, 9	311, 318

shows 15 collision risk scenario-specific target ships, their initial/end speeds, and initial course information. Most of the scenarios are encountered in a crossing situation; however, in the case of scenario no.7, involving ship-2 and ship-4, and scenario no.13, where ship-4 and ship-5 meet, the ships encounter a head-on situation. Moreover, in the case of scenario no.8, involving ship-2 and ship-5, and in scenario no.15, with ship-5 and ship-6, ship-5 overtakes at the sterns of ship-2 and ship-6.

The separation distances and CoRI results for each encounter scenario are shown in Figure 3, and these results are used to perform a detailed analysis of the collision risk between the ships. Figure 3a shows the separation distances over the navigation time for scenarios 1–15, and it indicates that most of the scenarios are close to the minimum separation distance of 3 NM. In Figure 3b, the near-collision situation occurred sequentially along with scenario-1 (Figure 4a situation), scenario-6 (Figure 5a situation), and scenario-4 (Figure 6a situation). Figure 3b represents the CoRI results for each scenario as well as a detailed analysis of risk-recognizable scenarios no.1, no.4, and no.6, which have a CoRI value of more than 50% [30,50].

Figure 4 shows the results of the ship tracks and the CoRI results of scenario no.1 (ship-i: ship-1, ship-j: ship-2), and ship-j overtakes from the starboard side of the ship. From the analysis of the scenario along with other encounter ships, it was seen that ship-1 changed its course to starboard to avoid ship-3, but, subsequently, ship-2 entering the Busan Port led to a collision risk situation. Then, ship-1 turned to the port side and avoided it owing to a collision risk with ship-2 entering the Busan Port. Figure 4a plots the 3-min vector ship tracks of ship-i, j with the VTSO ship domains at the CPA positions, and Figure 4b plots the CoRI results over time with the T, E, and A indices. Figure 4b shows that the CoRI also converges to zero as the T index converges to zero after 40 min. A risk situation with a CoRI value of 50% occurs from the starting point of the voyage to approximately 40 min. At that time, it can be seen that the counter risk E increases in the case of a collision proximity situation, and it then turns to the port side and decreases again.

Figure 5 shows the ship track and CoRI results of scenario no.4 (ship-i: ship-1, ship-j: ship-5). As in scenario no.1, ship-j overtakes from the right side of ship-i. Following the situation in Figure 4, ship-1 turned to the port side, followed by ship-2, and a dangerous situation occurred with ship-5 entering the Busan Port. Then, ship-1 slowed down after turning to the port side, and ship-5 turned to the starboard and entered the Busan Port. Figure 5a shows the 3-min vector ship track results of ship-i, j with the VTSO ship domains at the CPA positions, and Figure 5b plots the CoRI results over time using the T, E, and A indices. Figure 5b shows the risk situation with a CoRI value of 50% between 43 min and 47 min from the start of the voyage and a collision risk situation with a risk of 50% or more near 52 min. In addition, in the lower-risk interval, the T index also converges to zero. This indicates that, in Figure 5a, after ship-i rotates around the course at approximately 40 min, ship-j’s navigation and the course become similar, which results in a risk of more than 50%. In other words, after approximately 40 min, ship-1 turned to the port and avoided the collision situation with ship-5, and, thus, the encounter risk E decreased. At this time, the ship-to-ship proximity T according to the approach time decreased sharply owing to the deceleration of ship-1.

Figure 6 shows the ship track and CoRI results of scenario no.6 (ship-i: ship-2, ship-j: ship-3); ship-j crossed at the starboard of ship-i. After passing ship-1, ship-2 went through a dangerous situation with the tugboat ship-3 crossing, and, at this time, it turned toward the port and entered the Busan Port from the bow of ship-3. Figure 6a shows the 3-min vector ship tracks of ship-i, j with the VTSO ship domains at the CPA positions, and Figure 6b plots the CoRI results over time using the T, E, and A indices. In Figure 6b, it is shown that the CoRI value gradually increases to more than 50% from the starting point of the voyage to approximately 42.5 min, then converges to zero because the T index converges to zero after approximately 43 min. This indicates that, in Figure 6a, ship-i clears the collision by turning its course at approximately 42.5 min. In other words, the ship-to-ship proximity T according to the approach rapidly decreases as ship-2 turns to the port side to avoid a collision situation.

Figure 7 shows the DCPA and TCPA for scenarios 1, 4, and 6 over time. From the DCPA results in Figure 7a, it can be observed that the DCPA is also close to 0.5 NM in the range where the risk of scenarios 1, 4, and 6 is higher than 50%. In addition, the TCPA results in Figure 7b show that the T index converges to zero in the interval where the TCPA is negative, which results in a low risk value.

4. Collision Risk Assessment Support System

4.1. Collision Risk Assessment Algorithm

The algorithm used to evaluate the collision risk between the ships in a multi-ship environment is shown in Algorithm 1. The following variables are used: the number of ship combinations, ship information (static and dynamic data), minimum separation distance between ships, and collision risk index using the CoRI model.

Algorithm 1. Collision risk assessment algorithm in multi-ship environment.

1: Input:min_distance, ship_position/speed/course/dimensions/type/time, CoRI_threshold 2: Output: alarm, ship_no., risk_level 3:  while scenario_no. ≤ combination_no. 4:  if min_distance ≤ 3NM  &&  CoRI ≥ CoRI_threshold 5:  alarm = 1; 6:            ship_no. = combination_no.; 7:            risk_level = CoRI; 8:  else 9:  alarm = 0; 10:  end 11:  end

Algorithm 1 represents the procedure for the collision risk assessment algorithm and the input/output variables used in the collision risk assessment module at time t. The dynamic ship information is used as the input data. The min_dist represents the minimum distance between the vessels subject to the collision risk assessment (in nautical miles), the ship_position represents the latitude and longitude coordinates of the target ship-i, j, and the ship_speed represents the target ship-i, j course. The ship static information, such as the ship_dimensions of ship-i, j and the ship_type, are also used. The time variable ship_time represents the computational time for the collision risk assessment, and the CoRI_threshold represents the threshold value, which is the CoRI safety reference value set by the VTSO and RO to evaluate the collision risk in the VTS and RC centers.

4.2. System Configuration

The system used to support the collision risk assessment in multi-ship environments expresses the collision risk index and ship-to-ship situation information and generates an alarm if the risk assessment index is above the threshold set by the VTSO and RO. At this time, the VTSO and RO can click on the alarm to check the ship’s specifications and dynamic information along with the collision risk target ship-ID in the local waters to recommend the evacuation of the vessel and provide risk assessment information from the system, thus reducing or eliminating the risk of a collision.

A potential user interface of the collision RiASS, which supports the VTSO control and MASS RO remote control in a multi-ship environment, is shown in Figure 8.

When an alarm occurs in the collision risk assessment support system, the static information, such as the target ship type, dimensions (L: length, B: beam, D: drift) (m), and call sign, are expressed. In addition, the VTSO and RO can check the dynamic information at time t (s), such as speed (kts), separation distance between the ships (NM), DCPA (NM), and TCPA (min). The CoRI value is also displayed with the ship domain at the CPA position for an intuitive understanding of the ship-to-ship latitude and longitude coordinates (deg) in the local collision risk area. Additionally, the reference value for the alarm generation in the system was set at a risk of 50% or higher, and the CoRI value was set to 3.

5. Discussion and Conclusions

In this study, a collision risk assessment method and risk assessment support system were proposed to enhance the situational awareness of the VTSO and MASS RO in the event of a collision risk owing to an encounter between ships in a multi-ship environment in the VTS area.

The VTSO domain used in the risk assessment model is a ship domain that is statistically derived from the VTSO survey in the case of encounters between ships in coastal waters outside of the VTS area. The safety zone, which is the ship domain, applied in this study may have been larger than the safety zone of a waterway and anchorage in the VTS area of the port. In addition, there are limitations associated with this study: the risk analysis for near-collision scenarios at Busan Port did not reflect the unique characteristics of the port’s environmental factors because the characteristics of each port are different.

The efficiency of the proposed collision RiASS was initially verified only at the system stage. Therefore, the effectiveness of future VTSOs and MASS ROs and their improved situational awareness of the local sea risk situation owing to the use of the proposed system has not yet been confirmed.

The limitations of the three near-collision scenarios analyzed in this study are that the CoRI model was applied to the collision risk situation at the VTS area of Busan Port and not all the collision risk situations at the VTS areas at other ports.

In summary, following discussions on the introduction of a MASS by the IMO, the IALA proposed the consideration of the “interaction between VTS and the control of MASSs” and the “sharing of situational awareness of the waterway within the VTS environment” when implementing a system to support MASS operations. Therefore, this study proposes a real-time collision RiASS that allows the VTSO and MASS RO to receive situational information on risk situations in local waters along with quantitative data when near-collision situations occur in the multi-ship environment of the VTS area.

The risk evaluation of the RiASS system is based on the VTSO ship domain, which is a method used to predict possible collision risk situations in advance by moving the existing ship domain to the CPA location. It is a real-time CAS concept that generates an alarm if the risk value exceeds the safety standard set by the VTSO and MASS RO. To evaluate the validity of the proposed system, three near-collision-scenario risk analyses were performed at Busan Port. A risk assessment based on the ship encounter was conducted on all the possible combination cases of the risk assessment for a multi-ship environment. The changes in the TCPA, DCPA, and inter-ship distance were analyzed over time for three cases with a CoRI value of more than 50%, which is a risk recognition stage. The analysis confirmed that the TCPA was lowered within 10 min and the DCPA within approximately 0.5 nautical miles. Additionally, the separation distance between the ships was lowered to within 3 nautical miles. This can improve the situational awareness of the VTSO and MASS RO through alert alarms in the event of a near-collision situation between multiple ships in the VTS area, and the validity of the real-time CAS is confirmed through the system.

In the future, further research is necessary on safety areas that reflect the characteristics of the waterways and anchorages in ports, and the environment of each VTS area must be considered. In addition, in this paper, although the risk attitude of the VTSO was equally applied to the RO, a study on the RO’s attitude on the risk (or situation awareness) is necessary when the MASS vessel is operated later.