|
|
|
|
|
?iga Unuk and Milan Kuhta
A nonlinear semi-numeric and finite element analysis of three-point bending tests of notched polymer fiber-reinforced concrete prisms was performed. The computational and experimental results were compared in terms of the load-displacement behavior. The ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sabine Upnere, Iveta Novakova, Normunds Jekabsons, Andrejs Krasnikovs and Arturs Macanovskis
Concrete is a widely used material in various industries, including hazardous waste management. At the same time, its production creates a significant carbon footprint. Therefore, intensive research is being conducted to create more eco-friendly concrete...
ver más
|
|
|
|
|
|
|
|
|
|
|
Piero Antonio Zecca, Salvatore Bocchieri, Marina Borgese, Carolina Dolci, Alessandra Campobasso, Giovanni Battista, Alberto Caprioglio and Mario Raspanti
This scientific article investigates the mechanical properties of a novel three-dimensional-printing resin specifically designed for orthodontic aligners and compares it to other commonly used resins. The resin was made by blending two commercially avail...
ver más
|
|
|
|
|
|
|
|
|
|
|
Moritz Kuhtz, Jonas Richter, Jens Wiegand, Albert Langkamp, Andreas Hornig and Maik Gude
Carbon fibre-reinforced plastics (CFRP) are predestined for use in high-performance components due to their superior specific mechanical properties. In addition, these materials have the advantage that the material properties and in particular, the failu...
ver más
|
|
|
|
|
|
|
|
|
|
|
Thi Tuyet Trinh Nguyen, Van Bac Nguyen and Minh Quan Thai
In this paper, the flexural strength and buckling of the partially concrete-filled steel tubes (PCFST) under laterally repeated loads was investigated through three-point bending test configuration. Three-dimensional Finite Element (FE) models of the ben...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sabina Cherneva, Vladimir Petrunov, Vladimir Petkov, Vladimir Bogdanov and Silviya Simeonova
The mechanical properties, structure, and morphology of milled and 3D-printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, a...
ver más
|
|
|
|
|
|
|
|
|
|
|
Fei Xu, Qi Li, Tongze Ma, Yao Zhang, Junwei Li and Tao Bai
Concrete structures are subjected to various forms of damage in cold regions. However, the interfacial bonding properties of traditional concrete (NC) reinforced with textile-reinforced cementitious composite (TRECC) under freeze?thaw cycle damage have n...
ver más
|
|
|
|
|
|
|
|
|
|
|
Canan Akay, Gülce Çakmak, Mustafa Borga Donmez, Samir Abou-Ayash, Emre Mumcu, Suat Pat and Burak Yilmaz
Removable dental prostheses are commonly fabricated using polymethylmethacrylate, a material that does not have favorable mechanical properties and needs reinforcement with particles such as graphene. The aim of this study was to evaluate the flexural st...
ver más
|
|
|
|
|
|
|
|
|
|
|
Katarina Monkova, Peter Pavol Monka, Milan ?aludek, Pavel Beno, Romana Hricová and Anna ?meringaiová
Porous materials bring components not only direct advantages in the form of lightening of constructions, saving of production materials, or improvement of physical properties, but also secondary advantages, which are manifested as a result of their daily...
ver más
|
|
|
|
|
|
|
|
|
|
|
Nitesh Kumar, Ananda Babu, Alok Kumar Das and Ashish Kumar Srivastava
This paper presents an evaluation of the mechanical properties of nanocomposites when a lower concentration of nanoparticles graphene and ceramics are mixed with epoxy to determine the damping and stability characteristics of hybrid epoxy, using vibratio...
ver más
|
|
|
|
|
|