|
|
|
|
|
Liutauras Marcinauskas, ?ydrunas Kavaliauskas, Kamile Jonynaite, Rolandas Uscila, Mindaugas Aikas, Skirmantas Ker?ulis, Antanas Strak?ys, Arunas Stirke and Voitech Stankevic
A gliding arc discharge (GAD) plasma device has been developed and tested. Possible applications areas for GAD plasma could be microalgae suspension treatments and the creation of plasma-activated water. To understand its behavior, the influence of the i...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sadiq Gbagba, Lorenzo Maccioni and Franco Concli
In the shipbuilding, construction, automotive, and aerospace industries, welding is still a crucial manufacturing process because it can be utilized to create massive, intricate structures with exact dimensional specifications. These kinds of structures ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yoshinori Matsuda, Koji Kakutani and Hideyoshi Toyoda
This study developed an unattended electric weeder (UEW) to control floor weeds in an orchard greenhouse. The UEW was a motor-driven dolly equipped with a spark exposer. The spark exposer was constructed by applying an alternating voltage (10 kV) to a co...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sittichai Wangwiwattana and Koike Yoshikazu
Electrical fires are usually caused by contact heating, for which the mechanism of heat accumulation is currently not well understood. Previous studies done by many researchers were able to recognize the pattern of the electrical waveform, but the actual...
ver más
|
|
|
|
|
|
|
|
|
|
|
Qiongfang Yu, Liang Zhao and Yi Yang
For low-voltage three-phase systems, the deep fault arc features are difficult to extract, and the phase information has strong timing. This phenomenon leads to the problem of low accuracy of fault phase selection. This paper proposes a three-phase fault...
ver más
|
|
|
|
|
|
|
|
|
|
|
Feng Xu, Xiaoming Huang, Yi Lu and Zheren Zhang
This paper focuses on the soft normally open point (SNOP) which has no transformers and connects to the 10 kV distribution network through the arc suppression coil grounding mode. A mathematical model containing positive-, negative-, and zero-sequence co...
ver más
|
|
|
|
|
|
|
|
|
|
|
Van Thao Le, Dinh Si Mai, Van Thuc Dang, Duc Manh Dinh, Thi Hong Cao, Van Anh Nguyen
Pág. 01 - 11
This paper aims to investigate the fabrication of high strength low alloy (HSLA) steels by wire and arc-based directed energy deposition (WADED). Firstly, the relationship between the process variables (including the travel speed-V, the current-C, and th...
ver más
|
|
|
|
|
|
|
|
|
|
|
Luigi Nele, Giulio Mattera and Mario Vozza
Welding is one of the most complex industrial processes because it is challenging to model, control, and inspect. In particular, the quality inspection process is critical because it is a complex and time-consuming activity. This research aims to propose...
ver más
|
|
|
|
|
|
|
|
|
|
|
Dimas Okky Anggriawan, Audya Elisa Rheinanda, Muhammad Khanif Khafidli, Eka Prasetyono, Novie Ayub Windarko
Pág. 239 - 251
Series Arc Fault is one of the disturbances of arcing jump is caused by gas ionization between two ends of damaged conductors or broken wire forming a gap in the insulator. Series arc fault is the primary driver of electrical fire. However, lack of knowl...
ver más
|
|
|
|
|
|
|
|
|
|
|
João Roberto Sartori Moreno, Celso Alves Corrêa, Elisangela Aparecida da Silva Lizzi, Émillyn Ferreira Trevisani Olivio, Paulo Sergio Olivio Filho, Ana Carla Santos da Silva, Tiago Felipe de Abreu Santos
Pág. e49807
The objective of this study was to analyze the flux-cored arc welding (FCAW) welding parameters and microhardness levels on surface quality of 410 NiMo martensitic stainless-steel coatings. The parameters of the FCAW process applied to the coating, inclu...
ver más
|
|
|
|
|
|