|
|
|
|
|
Hongzhang Pan, Yongmei Zhu and Mingjiang Fang
Maraging steel is the material of deep sea pressure equipment. The characteristics of corrosion fatigue crack initiation in 18Ni (250) were investigated by performing a tensile fatigue test under different loading conditions. The mechanism of corrosion f...
ver más
|
|
|
|
|
|
|
|
|
|
|
Dong Qin, Xu Geng, Zhao Jie and Hu Yaoyu
The traditional study on fatigue strength for ship structures usually focuses on high cycle fatigue and ignores low cycle fatigue. However, given the recent trend towards large-scale ship development, the stress and deformation experienced by ship struct...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yuxuan Xia, Jingxia Yue, Jiankang Lei, Ke Yang and Yordan Garbatov
The welding residual stress re-distribution behavior during fatigue crack propagation in butt-welded high-strength steel plates for ship construction is investigated based on experimental test results and numerical analyses. The specimens? initial weldin...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jinfeng Liu, Guoqing Feng, Jiaying Wang, Huilong Ren, Wei Song and Panpan Lin
Welding defects are known to cause crack propagation and reduce structural fatigue performance. Based on the Paris theory of fracture mechanics, research is conducted on evaluation methods for analyzing fatigue crack propagation by adopting random loads ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Huating Chen, Yifan Zhuo, Yubo Jiao and Weigang Bao
The fatigue safety of cable-girder anchorage structures in cable-stayed bridges under long-term service has attracted much attention. For bridges located in seasonally cold regions, the effect of low-temperature environments should be considered when eva...
ver más
|
|
|
|
|
|
|
|
|
|
|
Abdulnaser M. Alshoaibi and Abdullateef H. Bashiri
The objective of this study is to examine the behavior of fatigue crack growth (FCG) in the mixed mode (I/II) of the AISI 316 austenitic stainless steel alloy, considering mode mixity angles of 30°, 45°, and 60°. This particular alloy is widely used in t...
ver más
|
|
|
|
|
|
|
|
|
|
|
Murat Demiral, Fethi Abbassi, Abolfazl Zahedi and Salih Akpinar
Single shear or single lap joints are the most prevalent type of adhesive joints used in advanced engineering applications, where they are exposed to fatigue loadings in their services. Although their mechanical performances under static loading have bee...
ver más
|
|
|
|
|
|
|
|
|
|
|
Murat Demiral, Fethi Abbassi, Riaz Muhammad and Salih Akpinar
Bonded joints used in wing sections and frames of aircraft structures are mostly exposed to cyclic loadings instead of static ones during their services. Bending types of dynamic loadings are mostly encountered. In this study, the fatigue response of a s...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhiqiang Xu, Yunxian Cui, Baoliang Li, Ketong Liu, Feiting Shi and Peng Cao
A fatigue test on the failure mode of flange shafts was conducted. The propagation characteristics of the initial crack at the junction between the shaft and the flange as well as its angle effect were studied. This study developed an analysis program of...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jingxia Yue, Jiankang Lei, Yordan Garbatov and Ke Yang
Many studies have shown that the linear elastic fracture mechanics (LEFM) method based on the stress intensity factor range (?K) has limitations that cannot be ignored. Due to neglecting the influence of plastic deformation near the crack tip, LEFM shows...
ver más
|
|
|
|
|
|