|
|
|
|
|
Khaqan Baluch, Heon-Joon Park, Kyuchan Ji and Sher Q. Baluch
Whilst numerical modelling is commonly used for simulation to check the design of water conveyance, sluicing and spillway structure design, the numerical modelling has rarely been compared with the physical model tests. The objective of this research pre...
ver más
|
|
|
|
|
|
|
|
|
|
|
Miroslav Dado, Marián Schwarz, Jozef Salva, Richard Jankovic and Richard Hnilica
The hand-held power sander is a frequently used tool in woodworking, and it is a significant source of risk in terms of dust, vibration, and, notably, noise. The purpose of a hand-held power sander manufacturer?s noise emission statement is to provide in...
ver más
|
|
|
|
|
|
|
|
|
|
|
Michael Frenzel, Enrico Baumgärtel, Steffen Marx and Manfred Curbach
This article presents the cracking and load-bearing behaviour of carbon-reinforced prismatic concrete tensile specimens. Grids with different geometries and impregnations were used as carbon reinforcement. In addition, the roving surfaces were partially ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jingsheng Lu, Guangrong Jin, Dongliang Li, Deqing Liang, Yong He, Lingli Shi, Yiqun Zhang and Youming Xiong
Gas from natural gas hydrate (NGH) is priced competitively with gas prices. Most marine NGH is stored in low cementing strata, which easily cause sand production problems, restricting the commercial production and environmental safety of NGH?s developmen...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hussein Ali Hussein, Sabah Ibrahim Wais and Khedir R. Khedir
In this study, superhydrophobic surfaces were developed by using a simple and environmentally friendly technique. The nano-network of candle soot (CS) as the byproduct of incomplete combustion of paraffin candle was directly coated onto both smooth and m...
ver más
|
|
|
|
|
|
|
|
|
|
|
Maciej Sydor, Radoslaw Mirski, Kinga Stuper-Szablewska and Tomasz Rogozinski
We hypothesized that the type of wood, in combination with the grit size of sandpapers, would affect sanding efficiency. Fixed factors were used in the experiment (a belt sander with pressure p = 3828 Pa, and a belt speed of vs = 14.5 m/s) as well as var...
ver más
|
|
|
|
|
|
|
|
|
|
|
Marta Pedzik, Tomasz Rogozinski, Jerzy Majka, Kinga Stuper-Szablewska, Petar Antov, Lubos Kristak, Richard Kminiak and Martin Kucerka
Wood dust generated during woodworking?particularly from hardwood species during sanding?poses a health and safety hazard to workers in the wood industry. This study aimed to determine the particle-size distribution of selected hardwood species and the c...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sheikh Ali Ahmed, Stergios Adamopoulos, Junqiu Li and Janka Kovacikova
Change of relative humidity (RH) in surrounding environment can greatly affect the physical and mechanical properties of wood-based panels. Commercially produced acetylated medium density fiberboard (MDF), Medite Tricoya®, was used in this study to predi...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hilary A. Sandler
Integrated weed management (IWM) has been part of cranberry cultivation since its inception in the early 19th century. Proper site and cultivar selection, good drainage, rapid vine establishment, and hand weeding are as important now for successful weed ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Emilia-Adela Salca, Tomasz Krystofiak and Barbara Lis
The objective of this study was to optimize the sanding and coating processes of black alder wood to promote and support its use in furniture manufacturing. Two criteria have been applied for process optimization, namely, the minimum surface roughness of...
ver más
|
|
|
|
|
|